Vic Collins' 1955 Chevrolet

From Kustomrama
Jump to: navigation, search
The inside of Vic's first truck all braced up before the chop in November of 2003. Photo by Ron Blaufeder, courtesy of Mark Wojcik.
Unlike the original Kopper Kart, 4 1/2 inches were taken out of the roof on Vic's truck. According to the magazine stories, Sam Barris only took out 4 inches when he chopped the original Kopper Kart. Photo by Ron Blaufeder, courtesy of Mark Wojcik.
Vic taking the first cut during the chop. Photo by Ron Blaufeder, courtesy of Mark Wojcik.
Photo by Ron Blaufeder, courtesy of Mark Wojcik.
A photo of Vic and Mark during the chop on the first truck. Photo by Ron Blaufeder, courtesy of Mark Wojcik.
4 1/2 inches measured up and ready to be cut out of the rear window. Photo by Ron Blaufeder, courtesy of Mark Wojcik.
An under progress photo of the he first Kopper Kart clone next to Barry Mazza's Aztec in November of 2003. Photo by Ron Blaufeder, courtesy of Mark Wojcik.
John Maurice's Kopper Kart clone as it sat when Vic received it in October of 2006. Photo courtesy of Mark Wojcik.
Photo courtesy of Mark Wojcik.
Working being done on the rear end of the Kopper Kart clone in January of 2007. Regular Studebaker pans were used in the rear, while the front ones came from two rare Studebaker wagons. Photo courtesy of Mark Wojcik.
Photo courtesy of Mark Wojcik.
The truck as it sat in July of 2007. Photo courtesy of Mark Wojcik.
Photo courtesy of Mark Wojcik.
Photo courtesy of Mark Wojcik.
The body being prepped for paint in January of 2008. Photo courtesy of Mark Wojcik.
Photo courtesy of Mark Wojcik.
After spending hundreds of hours sanding the body, paint could finally be applied late in January of 2008. Here is Mark taping off the scallops. Photo courtesy of Mark Wojcik.
Photo courtesy of Mark Wojcik.
Photo courtesy of Mark Wojcik.
Photo courtesy of Mark Wojcik.
Photos of the truck taken late in February of 2008, before it was shipped off to Jim Laga for detailing. Photo courtesy of Mark Wojcik.
Ph3to courtesy of Mark Wojcik.
Photo courtesy of Mark Wojcik.
Jim Laga spent a week detailing the truck before it was sent to Alan Johnson for pinstriping March 1, 2008, just days before the debut at the Detroit Autorama. Photo courtesy of Mark Wojcik.
Photo courtesy of Mark Wojcik.
Photo courtesy of Mark Wojcik.
Vic having a seat in the truck. Photo courtesy of Mark Wojcik.
The copper leaf lettering was done by Alan Johnson and Bill Riedel. Photo courtesy of Mark Wojcik.
An overhead shot of the build team. Mark in front, then Daran, Vic, and Ron to the right. Photo courtesy of Mark Wojcik.
The Kopper Kart clone at Darryl Starbird's Tulsa show in February of 2009. Photo courtesy of Mark Wojcik.
Photo courtesy of Mark Wojcik.
October 3-5, 2014 the Kopper Kart Klone was one of the featured cars in the historic custom car exhibition at the Customs by the Sea car show in Wildwood, New Jersey.
The Kopper Kart Klone and Harry Fry's 1937 Ford Cabriolet in the inner circle at the 2014 Customs by the Sea. Photo by Sondre Kvipt - Kustomrama.


1955 Chevrolet truck owned by Victor "Vic" Collins of Rahway, New Jersey. Vic's truck is a clone of George Barris' 1955 Chevrolet truck, better known as the Kopper Kart. Vic has been fascinated by the Kopper Kart since he first saw it at age 11 in 1975. At the time he and his father were building model cars, and old custom car magazines were used for inspiration. George's wild truck made a huge impression on the young kid, and 24 years later, in 1999, he decided that he wanted to clone it. A 1955 GMC truck was bough at an estate sale. Vic's younger brother Ed helped Vic pick up the project. Back home, Vic called Barry Mazza, the owner of the Aztec, knowing he had Studebaker pans. At one point Barry was thinking of cloning the Aztec. He bought the real deal instead, and kept on to the pans. A deal was made and Barry agreed to sell the pans to Vic. With help from two friends, Vic and Ed cut the body apart with a Sawsall and began the sectioning job. Early 2000 Vic asked his buddy Mark Wojcik at Customs by Flash if he was interested in helping him with the Kopper Kart project. Mark told Vic to bring it down to his shop in Howell, New Jersey. During the build, Mark posted photos of the project on the HAMB. After the HAMB threads were published, Mark and Vic found out that John Maurice of Maine was also working on a clone of the Kopper Kart truck. This made Vic even more determined to complete his dream build.[1] After working on and off the truck for some years, the project stalled several times due to other projects getting priority. As Marc and Vic felt that they were getting burned out working on the truck, they decided to buy a better project for their clone. A 1955 Chevrolet truck was purchased in 2004, and the build team started from scratch, cleaning up the rust and learning from past mistakes.


John Maurice started his build in the fall of 2000. The truck John started with was a Christmas gift from his wife Alyssa. John had first spotted the truck 8 years earlier at a used car dealership. Countless hours were spent researching the truck along with many years tracking down hard to find parts, such as two Studebaker wagon rear pans, and a 1950 Mercury accessory horn ring. When John started the build, nobody knew for sure what became of the original Kopper Kart. During his research, John was able to track down Paul Blasberg, the last known owner of the famous truck. Paul owned the truck in the early to mid 1960s. After having a lot of fun with it, the six-cylinder engine was pulled to make way for a 3/4 race Cadillac mill in preparation for running at the dragstrip. The truck was never reassembled again, and it was left outside to deteriorate. Paul's wife told John that it had really "gone to pot" from the rainwater getting through the exterior upholstery. A man came to the couple and offered to fix up the truck. Instead he ended up stripping it. As Mr. and Mrs. Paul Blasberg had already had their fun with the truck, they weren't too worried about the situation.[2] Supposedly the bed and cab went separate ways.[3]


John's truck had a rebuilt 235 engine that fired up without any effort. He lowered the truck by flipping the axles over the springs, and installed a 3-speed overdrive that he scored on eBay. He drove it like that in the summer of 2001. John had never welded sheet metal before he began on the truck. That winter he started installing patch panels in his unheated garage. By February of 2002 it was ready for the chop. In March, John and his father Bill chopped the top 4 inches. John used the Spotlite Custom Pickups magazine as a guide during the chop, since it had a feature on the chopping of the original Kopper Kart. Shortly after the top was chopped, John sectioned the truck for the first time. Most of the vintage magazines stated that the Kopper Kart was sectioned 5 1/2 inches. John learned trough trial and error that 5 1/2 would be too much. The rear fenders were sectioned as well, and extended to give the car a long look. From 2003 - 2005 several other priorities kept John from working on the truck. In 2005 he re-sectioned the cab with some valuable help from his friend Steve McCann. That change really brought the cab into the right proportion that John wanted. In 2006 John and his wife decided to move to New York City so she could pursue her dream of acting professionally. He realized that he was not able to complete the project living in the big city, so he decided to sell it off. He knew from the HAMB that Vic's project had stalled due to some problems with the cab, so he sent Vic an email asking if he was interested in buying what he had, parts or the complete project. After looking at photos of John's project, both Vic and Marc were so impressed that they decided to take over the whole project. They received the truck in October of 2006, and within few months the metal work was completed and the car was covered in plastic filler, primed and mocked up. This in-progress version was shown at the 2007 Lead East car show in Parsippany, New Jersey.[1]


When Vic bought the truck, John had also acquired and installed a 1954 Chevrolet engine along with the correct Corvette intake. Just like the original Kopper Kart, the clone was fit with dual headlights. The custom grill was comprised by four highly modified 1955 Plymouth grill bars, expanded mesh sheet metal, and a 1955 Cadillac Autronic Eye. The Studebaker wagon pans were installed up front, while the two from a coupe were installed in the rear. 1956 Mercury wagon taillights were encased with modified 1949 Chevrolet license plate guards and chromed mesh. The hood and fenders were peaked. The drip rails were shaved, and the hood and door corners were rounded. Quad parking lights were installed in custom formed housings. Wheel covers from a 1957 Oldsmobile were installed with custom bullets and spinners. The side trim was made from copper plated 3/4 half oval stock with perforated metal inserts. Parts from both of the Kopper Karts were used in the final build, as Vic and Mark were pulling parts off of one of the rejected trucks to fill in the gaps. Once the bodywork was done, Mark gave the car it's signature paint job. 3 coats of white sealer was followed by 3 coats of base, 4 coats of pearl and 2 coats of intercoat clear. The clear was then scuffed before the scallops were taped and Mark shot 3 coats of base, 3 coats of Candy Copper and 4 coats of clear.[4] After Marc and his crew got the truck from John, they put 3100 hours into it. Working only part time on the truck, it took 16 months to complete the build. In addition to John, Mark and Vic, Ron Blaudfeder, Daran Rumbaugh, John Maurice, Bill Sincox, Joe Siclari, and Ed Collins were also instrumental in the build.[1] The clone was pinstriped by Alan Johnson, and the copper leaf lettering was done by Alan and Bill Riedel.[5] The interior was stitched by Everlast Upholstery in Linden, New Jersey. The build was completed in 2008, making it's debut at the Detroit Autorama March 7. This was in fact on the 50th anniversary of the original Kopper Kart appearing at the show.[1]


Magazine Features and Appearances

Kustoms Illustrated Issue 15
Kustoms Illustrated Issue 16
Kustoms Illustrated Issue 17


The HAMB Build Threads

CHOPPIN THE KART!!!
CHOPPING THE KART, PART 2
ANOTHER UPDATE...FUNNY LOOKING REAR END.
PROJECT UPDATE
JUST PUSHED IT OUTSIDE.....
KART UPDATE
ONE GIANT STEP...PAINT!
KOPPER KART PROGRESS
THIS IS IT! LAST UPDATE!!!!!!!
FINISHED IT...ONTO THE TRAILER!
YOU'RE SICK OF THESE UPDATE, I KNOW!


References




 

Did you enjoy this article?

Kustomrama is an encyclopedia dedicated to preserve, share and protect traditional hot rod and custom car history from all over the world.




Can you help us make this article better?

Please get in touch with us at mail@kustomrama.com if you have additional information or photos to share about Vic Collins' 1955 Chevrolet.


This article was made possible by:

SunTec Auto Glass - Auto Glass Services on Vintage and Classic Cars
Finding a replacement windshield, back or side glass can be a difficult task when restoring your vintage or custom classic car. It doesn't have to be though now with auto glass specialist companies like www.suntecautoglass.com. They can source OEM or OEM-equivalent glass for older makes/models; which will ensure a proper fit every time. Check them out for more details!

Do you want to see your company here? Click here for more info about how you can advertise your business on Kustomrama.


Personal tools
Help us
facebook