Henry Contreras' 1955 Chevrolet
Hot Rod Magazine Cover Car
An early version of Henry's Chevrolet, featuring a two-tone paint job, was featured on the cover of Hot Rod Magazine January 1957. This version sported a custom grille made from a 1954 Pontiac center grille bar that had been fit with two roadster headlights turned around to form bullets. Cavity in the grille was constructed from round tubing. The hood was nosed, peaked and louvered, and the doorhandles were shaved. This version of the car was also featured in Trend Book 143 Restyle Your Car.
Henry had pushbuttons installed under the dash to open the doors from the inside. On the outside, on the chrome strip that starts on the door and continues along the quarter, Henry installed a thin piece of rubber on the door part of the chrome strip. The rubber was trimmed to the size of the strip. On the two fastener studs that held it to the body, they taped a part of the stud, so that when they bolted the chrome strip to the door it was insulated. Then they double nut one stud and ran a 12 volt wire from the fuse box to the door chrome strip. This made the chrome strip hot, but as it was insulated nothing would happen. They then installed the door solenoids with little cables to the door latch inside the door. They wired the solenoids so when you shorted them, they would be activated. In order to activate the solenoids, you had to short out the chrome strip on the door that was hot, to the strip on the rear quarter panel that was grounded. What Henry then would do to open the door was to take a key or coin and short the door strip in the gap between the door and quarter panel. That would suck in the solenoid plunger, pull the cable and open the door latch. Henry remembers that nobody would figure out how he opened the doors. Everyone looked for push buttons under the rocker panels, pushing the chrome strip and so on. In order to fool people off, Henry would hide a coin in his hand, and act like he was pushing on something to throw them off. The guys would them get on their hands and knees to feel under the car because they thought he was doing it with his foot. The car was lowered by C'ing the frame, cutting coils and removing leafs.
Restyled by Branson's Custom Shop
Henry's good friend Joe Navarro worked at Branson's Custom Shop, and it was Joe that painted the car. The paint job on Henry's Chevrolet was Joe's first Candy Paint Job. The car went through several version, and it didn't take long before Henry removed the vertical side trim pieces and installed a pair of 1956 Packard taillight lenses. The rear fenders were extended 6 inches during the operation. Round rod was used to french-in and smooth the taillight openings. Up front, the parking lights were shaved, and the front bumper was replaced with a gravel pan that featured two bumperettes. Side pipes that ran along the rocker panels were also installed along with a brand new interior. The upholstery featured rolled and pleated setas, doors panels, kick panels and floor. This version was lacquered a brilliant red, and can be seen in Custom Cars May 1959.
Henry's club, the Rogues of Long Beach was a pretty good sized club, and in order to become a member, you had to have a nice ride. Primered cars were not accepted, unless it was in a customizing stage. If that was the case, you had a certain time to finish the car. Henry and his friends used to cruise Bellflower Blvd in Bellflower, and they hang out at the Clock drive in restaurant.
Later on, the car received a Blue paint job. The blue version didn't have lake pipes, and it was upgraded with a more modern tube grille and chromed wheels. After that the car received a Red paint job and a DeSoto grille. This version ran a rolled pan in the rear instead of a bumper. The rolled pan featured an inset license plate and integrated chromed strips. The roof was later painted white. Another incarnation of this version was Purple with a white roof.
Sold to Ron Gomez
Henry sold the Chevrolet to Ron Gomez of Los Angeles, California. Ron still owned the car in 2013. By then the car had been sitting for many years, and it needed a lot of work. Ron's intention was to restore the car after he had completed a Packard he was building.
In 2016 Ron Gomez sold the Chevrolet to Sam Freeman and Richard Mann of Freeman Automotive Design in Santa Barbara, California. November the same year Sam told Kustomrama that he and Richard are working on the car, restoring it back to one of the later versions; "We don't want to undo all the custom body work, so it will be one of the later versions of the car, but it will look different from anything that has been done to it so far. We will talk to Henry Contreras to see what he likes about the car, and what he would like to see done with it. We want to make it like the car would be if he still owned it and kept working on it." During the restoration, Sam and Richard upgraded the chassis, installing sway bars front and back, along with a triangulated four link in the back in order to make the old custom drive and handle better.
Magazine Features and Appearances
Did you enjoy this article?
Kustomrama is an online encyclopedia dedicated to traditional hot rod and custom cars. Our mission is to protect, preserve and share traditional hot rod custom car history from all over the world.
- Find out how you can become a contributor.
- Forward this article to a friend.
- Subscribe to our newsletter and receive updates on Henry Contreras' 1955 Chevrolet and other subjects featured on Kustomrama.
Help us make this article better
If you have additional information, photos, feedback or corrections about Henry Contreras' 1955 Chevrolet, please get in touch with Kustomrama at: email@example.com.
This Article Was Made Possible By:
SunTec Auto Glass - Auto Glass Services on Vintage and Classic Cars
Finding a replacement windshield, back or side glass can be a difficult task when restoring your vintage or custom classic car. It doesn't have to be though now with auto glass specialist companies like www.suntecautoglass.com. They can source OEM or OEM-equivalent glass for older makes/models; which will ensure a proper fit every time. Check them out for more details!
Do you want to see your company here? Click here for more info about how you can become a Kustomrama advertiser and supporter.